ZONE AMPLIFIER ZAA ZAA C AUTION AVIS 1 SAFETY INSTRUCTIONS 1 GENERAL USE (용도) 1 I NSTALLATIONS 2 F. Jedia JPAA/JPAA Amplifier Functions · JPAA Operating Instructions. Legislation and Compliance. RoHS Status: Not Applicable. Statement of. מגברי JDM היפרטרוניקס רכיבים וחלקי אלקטרוניקה מערכות כריזה והגברה מוצרי חשמל מגבר מיקסר חכם ל- 5 איזורי כריזה W. ZAA: A/A. ZAA: A/
|Published (Last):||5 February 2007|
|PDF File Size:||17.21 Mb|
|ePub File Size:||13.10 Mb|
|Price:||Free* [*Free Regsitration Required]|
Connect the power cord with safety after check of AC power. Second, you can increase input volume to the position “0” of LED indicator. When not using microphoneturn microphone “off”.
Be sure rear of amplifier is securely mounted to rack. Connect each connection of amplifier perfectly, if not, it maybe Caused hum, damage, electric shock in case of mis-connecting. Use LAN cable within m distance. For phantom, please push phantom switch to supply with P.
It’s a community-based project which helps to repair anything. Cable for audio line za-120a be used by shield cable. Do not drop objects or spill liquids into the inside of the apparatus.
The apparatus shall not be exposed to dripping or splashing and no object filled with liquids, such as vases, shall be place on the apparatus. To prevent electric shock, do not open top cover. Then, attenuation function jmd the main amplifier are reset and zone power-out is converted to HI impedance power output.
In case data are supplied to amplifier, send LED indicator lights. Out put impedance should be ohms more for pre-amp operation.
JD-MEDIA ZA-1120A ZA-1240A ATT. ZONE AMPLIFIER
For the direct output, use spk zone 4 and set speaker ATT. If clip indicator zq-1120a output meter is turn-on, please turn GAIN control to the clock-otherwise for the optimum internal operstion. Users can extend cable at 30m MAX. Turn gain volume and level controls of front panel to the clock-otherwise completely when you use phantom power.
This is RJ45 connector for power za-11200a of audio, data, make sure that 4pairs LAN cable is necessary for optimum operation. T remote PTT level.
The following is priority ranking against all signal inputs of system and priority signal is “NO” “OFF” automatically. ZAA, A havel been designed to use P. Remote controller RC is prior to any other prioroty priority za-11120a activated, an signals are closed But, P. Do not install this apparatus in a confined space such as a book case or similar unit. If not, speaker may get harmful due to loud jxm power by power shock. Maximum power output per zone speaker.
If all call switch, P.
ZAA/A/A > Product Information | PA/VA | JD-MEDIA
This is to prevent is to prevent mistake from remote controller RC T MIC remote control. Secound, you can increase input volume to the position “0” of LED indicator. T MIC signal can be activated za-11120a spite of priority.
You can hear telephone ring Via speaker from other office in the night.
מגברי JDM | מגבר מיקסר חכם ל- 5 איזורי כריזה W | היפרטרוניקס
This makes you replay, stop recorded message of the memory bank M1-M6 one time without setting repeat function. Install at the place, not bending curved. Pressing one of the zone button 1 to 5 delegates the signal to the desired loud speaker zone. Busy means under operating of “TALK” or digital message. All signals can be recorded but recording out can not be adjusted by master volume because recording output is in the front of circuit of master volume control.
Locate this apparatus away from heat source, such as radiators or other device that produce heat. Third, contact terminal to what you want. The stereo signal of the connected sound sources gets internally converted into a manual signal.
Amplifier P.A. 5 zone JDM ZA-1120A
Please pay close attention to the cooling az-1120a. Keep in mind the following when connecting the apparatus. Never block the air vents in the sides and front of the amplifier the following is figure of air-flow.
This apparatus should be serviced by qualified service person. This function is same as that of “TALK” or “message” operation. This is for pre signal or alert signal. It is best suited for call and message transmission installation with alert systems, music in industrial enterprises, offices, congregation halls and sport centers, schools, churches, hospitals, super-maket, and other similar occasions.
The corresponding LED indicator lights. Install equipment as follow conditions.