JBL H (8Ohm). Unavailable. Category of diameter 12 inch / cm; Znom 8 ohm; Weight volume is not set, then delivery by plane is not possible. Brand New JBL H 12″ Aftermarket Recone Kit, 8 ohm. Parts specifications: Cone: 12″ outside diameter, ″ deep, ″ voice coil opening; Voice. Subwoofer JBL H. General specifications: diameter 12 inches, maximum power W. Thiele-Small parameters: frequency of self resonance Fs=75 Hz, .
|Published (Last):||12 February 2015|
|PDF File Size:||12.20 Mb|
|ePub File Size:||6.49 Mb|
|Price:||Free* [*Free Regsitration Required]|
I think they both fall inbetween the “producer” and “reproducer” sound Dance to the radio. Differences jhl achieved in cone composition, coil windings, and VC former material. Logged “can you make them sing better?
But it has been a few years. I’ve been thinking of replacing my ‘s with ‘s down the road a bit and 2022 ‘s can be reconed as ‘s then that could be an option If we knew what the hell we were doing, we wouldn’t call it research would we. With proper processing do you think that it would be a good idea to just stick the in and work it out, while re-coning the The time now jbll It’s really a mid-range, a mid-bass at best. All that being said, my jjbl post was pre-emptive of checking the VC, which didnt seem to be effected at all.
I thought the magnet slab was thicker. The letter following the is used to designate the impedence. I used them as both side fill monitor and full range interchangeably and the has better low end while the is better for vocals.
The Marketplace for Musicians |
My name is Scott, as 202h give me more power Scottie!! The letter suffix represents the impedance, not frequency range of the speaker. This message comes from JBL Dog.
JBL, I have compared these side by side and could not find any difference in the basket.
Do what Tim recommended and give Charlie Tappa a call. Ie putting jbp kit in an E and so forth. Extra Tabs by vBulletin Hispano.
JBL 2022H 12″ Woofer Speaker Driver 8 Ohm
Is it LF or MF and can it be reconed to a ? Hi subwolf, thanks for the info. None were specifically for “mid range”. I do have a set of ‘s sitting around but they are the midrange version. Sing in the shower. You will have created something.
I guess you would call it JBL’s “midline” series driver. For a temporary fix I removed an older cone from another torched woofer, removed its suspension and dustcap, carefully removed the dustcap from the jbl and trimmed the glue from the cone as well as I could. By that I mean the kits will interchange physically. Thanks to everyone, good info all around.
Generally it will be more like the kit you put in it than the original-but will not have the exact same performance. I don’t know anything about the In most cases-similar 0222h JBLS can be reconed “kinda” as different model.
February 18, The differences in a 12″ driver in a 4 way system vs its 2-way sibling’s frequency response would be a huge factor, right?
Please login or register. You will get an enormous reward. All times are GMT I was under the thought that the suffix was also something that showed intent or use of the driver eg- a single driver with a 16ohm impedance would be used for a total 3 or 4 way system impedance of 8 ohms, but a single 4 ohm driver would be used for a 2 way system impedance of 8 ohms There was a ridge left behind from the old dustcap glue so I had to score the new cone near the former to get it to lay down flat, but once all the pre-fit was done, glue-ing it in wasnt too big of an issue rubber cement Read times Brian Elstro Jr.