I am a Dek

IPC Moisture Sensitivity Classification for Non-IC Components. Content Provider Association Connecting Electronics Industries [IPC]. IPC, PWB Assembly Sol- dering Process Guideline for. Electronic Components. • IPC, Moisture Sensitiv- ity Classification for Non-IC. Components. and Use of Moisture/Reflow Sensitive Surface Mount Devices). This standard supersedes IPC Developed by ECA, IPC and JEDEC.

Author: Vom Gugor
Country: Niger
Language: English (Spanish)
Genre: Sex
Published (Last): 22 July 2004
Pages: 418
PDF File Size: 10.94 Mb
ePub File Size: 15.35 Mb
ISBN: 796-9-94605-909-3
Downloads: 53925
Price: Free* [*Free Regsitration Required]
Uploader: Nikree

Once a Wafflepack is chosen all components of that size for the entire P. Suppliers should attempt to provide a best fit solution without incurring extensive tooling costs. Tray covers will also consists of black static dissipative material held to the base with a one piece clip. Each moisture barrier bag may contain up to 10 PWBs of size in2 per side or greater, and smaller boards may be packaged up to 25 per bag.

These carriers shall support the body of the component, maintain all physical lead dimensions, and allow visibility of the contact shall be such that no stress is applied to the leads.

Waffle pack dimensions should remain the same for subsequent lots of the same component type. Parts do not have to be pre-oriented, but 9053 be face up. All components must be loaded into black static dissipative 2″x2″ vacuum release trays.

The Gel retention level must be the minimum required to hold the component with a mesh size that adequately supports the component and allows the component to be released with vacuum applied. SMI only General Requirements: So typically paper as it enters the waste stream Do not handle with bare hands; use clean, lint free cotton gloves when handling. Parts must be loaded consecutively from left to right, proceeding from top to bottom as viewed with the notch of the waffle pack positioned in the upper left hand corner with a consistent separation between rows and columns.

  EKOSISTEM ESTUARI PDF

The packaging shall allow the polarity or part number markings to be visible for each device. Use of newsprint, excelsior, or loosed fill expanded polystyrene is not upc as a means of cushioning.

Packaging Requirement Codes

Gel Trays must be labeled on the cover and the bottom of the base with the supplier lot number and part number, PO number and BAE part number. The parts must not be held in the pockets by supplementary means within the tray.

Matte finish waffle packs should be used if available. Components will be covered with a lint free filter paper insert s between the top of the component and the bottom of the cover. Moisture content prior to packaging shall not exceed 0.

All waffle packs containing items that are ESD sensitive diodes, 9530 circuits, etc. The carrier shall be of a construction to allow component removal without tooling.

Items that are gold plated or have a 16 finish or lower shall contain the following note marked on exterior of container: Elements or components that are Class 0 Sensitive shall be clearly marked as Class 0 on the external surface of the packaging. Use of any static generating material is strictly prohibited.

Moisture content may be assured by documented process controls or appropriate testing. Tape and Reel Only General Requirements: Moisture transfer refers to the fact that certain solid waste Leaded surface mount technology electronic components must be packaged such that component lead integrity is not adversely affected during shipping by contact with the packaging.

  DM74LS151N DATASHEET PDF

Gel Trays should remain the same for subsequent lots of the same component type. Multiple boards in an MBB shall be separated by slip sheets or other appropriate materials such as pink poly bags. Matrix Tray General Requirements: Waffle pack covers will also consists of black static dissipative material. Specific packaging requirements will be provided by the using factory through the supplier electronic replenishment process.

Tubes Only General Requirements: All the components shall be oriented in the same direction according to polarity or pin one markings. Use of newsprint, excelsior or loose fill expanded polystyrene shall be avoided as a means of cushioning. Moisture Sensitive devices shall be packaged in moisture proof, conductive material or packaged in moisture proof antistatic material with external conductive field shielding barrier.

Each moisture barrier bag shall be marked with the part number, date code, quantity, and serial numbers of the PWBs enclosed. Additional information on this requirement can be found at the following site: Compliance Commitments related to the manufacture and.

Packaging Requirement Codes

Special Packaging Package parts per instructions specified by purchase order or subcontracts, ipx. Parts should be pre-oriented, but must be face up. An exception for through-hole radial components, bulkhead-mounted connectors, and cable connectors is best commercial practice.