I am a Dek

The capability to select a TE trigger on the HT12E or a DATA trigger on the HT12A further enhances the application flexibility of the 2 12 series of encoders. HT12E Datasheet, HT12E Holtek Encoder Datasheet, buy HT12E Encoder IC. The capa- bility to select a TE trigger on the HT12E or a. DATA trigger on the HT12A/B/C further en- hances the application flexibility of the 2.

Author: Mazujora Dubei
Country: Mongolia
Language: English (Spanish)
Genre: Music
Published (Last): 25 July 2011
Pages: 67
PDF File Size: 9.73 Mb
ePub File Size: 8.96 Mb
ISBN: 778-8-40547-630-3
Downloads: 34614
Price: Free* [*Free Regsitration Required]
Uploader: Arashikora

Dstasheet two ICs together form an Encoder and Decoder pair. The encoded bit can be obtained from the Dout pin pin This cycle is repeated as long as TE is kept low. It encodes the 12 bit parallel data into serial for transmission through an RF transmitter. The primary function of HT12E is to encode a bit and send it out through the output pin. For decoding a data the IC will requires an oscillator, luckily this IC has one in-built.

HT12A/HT12E – Product Details – Holtek

As soon as TE returns to high, the encoder output completes its final cycle and then stops. We should set the bits in same pattern on Encoder and Decoder IC to pair them. Choosing Motor For Robots. This data should be sent to the HT12D for gt12e, it can either be sent directly through a wire or by using a wireless medium like RF or IR.

It is mainly used in interfacing RF and infrared nt12e. Pull the Transmission Enable pin pin 14 to ground to activate transmission. HT12E has a transmission enable pin which is active low. The Encoded 12 bit output data can be obtained from this pin.

  DKVM-8E MANUAL PDF

These 12 bits are divided into 8 address bits and 4 data bits.

HT12E Datasheet

Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. Interface SD Card with Arduino. A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. You can know to set up the HT12D after this from here. Virgin Galactic — Commercial Space Flight. Can range from 2.

In this image I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can make any changes on these 4-bits and they will be reflected on the output side of the HT12D decoder IC. The IC is has a wide range of operating voltage from 2.

It is very important that your Decoder should also have this same address for them to talk to each other. What is Web Browser.

Supply voltage; 5V 2. These four pins are used to send data, the data encoded here will be decoded on Bt12e IC sharing the same address bits. HT12E is an encoder integrated circuit of 2 12 series of encoders. They can also be connected to switches to manually send and receive data. Connected to the Ground of circuit.

HT12E begins a 4-word transmission cycle upon receipt of a transmission enable.

  DAVID MITCHELL DER WOLKENATLAS PDF

HT12E Encoder IC

In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. SPI Module of Arduino. These are the 8-bit address bits, which is used to protect your data.

They are paired with 2 12 series of dtaasheet for use in remote control system applications. Interface GPS with Arduino.

This pin has to be connected to Ground 0V to enable the Transmission. The IC has a built in oscillator. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. The 4-bit data that has to be sent has to be given to the pins AD0 to AD1 and an address of datasheet has to be set using the pins A0 to A7. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you.

Choosing Battery for Robots. Simply put, HT12E converts the parallel inputs into serial output.

If you want security you can connect any of the 8 pins to 5V to make it high. This oscillator can be used by connecting these two pins through a 1M Resistor. Skip to main content. Submitted by admin on 30 October Transmission enable; active low.

This high-density System-in-Package SiP integrates controller, power switches, and support components.