I am a Dek

Mitsubishi FR-SF spindle drive manual. Uploaded by. Zeynel Ulusoy. USA- E* AC SPINDLE DRIV TROUBLESHOOTING, i A D V A N C E D AND . Hi Guys, I Replaced the power supply (SF-PW) on this spindle drive about 3 months ago and it was working fine for the last 3 months. For the. Mitsubishi vector Inverter Motor (SF-V5RU Series), English, , MB. FR -A/F/E/D SERIES TECHNICAL MANUAL, English,

Author: Faehn Kazizuru
Country: Malawi
Language: English (Spanish)
Genre: Sex
Published (Last): 21 June 2013
Pages: 257
PDF File Size: 3.86 Mb
ePub File Size: 9.59 Mb
ISBN: 161-4-49845-447-5
Downloads: 98978
Price: Free* [*Free Regsitration Required]
Uploader: Samushura

By referencing Section 4.

The control signal cable o Check that the cables are 0 Correctly connect them. This website or its third-party tools use cookies, which are necessary to its functioning and required to achieve the purposes illustrated in the cookie policy.

You must buy the exact same part number, as they are calibrated for different current levels. Note To check the occurrence o If the signal output is b If the alarm does not saturated when it exceeds occur, 10 V because a too high speed decrease the parameter is set, check that the volt- values of VKP and VKI.

Skip to main content. Direction of orientation rotation set by parameter ORS2 Same orientation direction as former 1 PRE rotation Forward 2 Orientation of motor forward rotation rotation Reverse 3 Orientation of motor reverse rotation rotation. It seems I found a typo or two in the charts that caused me great confusion. GRB4 5 is weak. The magnification of 22 PG2 orientation 2nd deceleration point by gear is st.

  EL ATRAHASIS PDF

Note 2 Since other volume have been set at factory, do not adjust them. Started machine again with the door of the spindle drive still open.

MITSUBISHI FREQROL Spindle drive

Refer to M series side to the encoder. When installing any test apparatus on a portion to be tested, take care not to touch any portion being grounded. Warranty Why buy an unknown, used drive with little life left? This item was removed from aWorking Machine, and i When decreasing PGl, point a approaches point c. Appendix 11 Table 1.

Encoder Magnesensor Spindle The spindle rotational angle at which orienta- creep speed starts is set. Set to idjust orientation for the respective rear. Hi Folks I hope you guys can help me.

Inverters-FREQROL Manual Download | MITSUBISHI ELECTRIC FA

Note Adjust the stop position point d using the para- meter PST. The number of gear teeth on the spindle However, on the NC 39 freqgol 25 side against the gear 00 is converted screen, it is in the into hexadecimal notation and set.

Increments a value on the display area. The gear rate is ffr-sf Number of gear by the number of gear – – – teeth on spin- teeth on the spindle dle side.

So, it is normal for the spindle controller LED to show different rpms than your cnc monitor. Motion C – Only the alarm lamp lights, but the operation continues. Spindle para- Sets the gear ratio between the spindle and sgear 0 spindle encoder.

  HACER PARA TRANSFORMAR MARITZA MONTERO PDF

Common Signal, description, waveform Example of waveform State which the magnesensor mounting disk rotates at 10 rpm CH4 u–ci I. Does it vary remarkably depending on the time fr-sff

Mitsubishi FR-SF: Industrial Automation, Control | eBay

The signal from the 0 Set the parameter of the 0 Adjust the related control encoder which contains amplifier as follows. SF-CA card is defective. When the orientation time becomes long because the time period on which the spindle rotates at a creep speed point b to c is long, decrease PGl or in- crease OSP in the manner that the spindle does not overrun when it stops.

In EHG, in-position aint exci- output is held. Freqroll Appendix 3 2.

To my knowledge it looks like one is used for acceleration and one for decceleration. Remove the P flat head screw which fastens the fan motor main body and the fan motor main unit freqorl be dis- mounted from the fan case.

These parameters are sent from the NC when the spindle amplifier is linked with the bus line.