I am a Dek

ASTM D is a test method used to study the compressive properties of a composite laminate that has a hole cut into it. The GD fixture meets the requirements of ASTM D for open-hole compressive strength testing of fiber-reinforced polymer-matrix composite. The ASTM D / DM fixture is used to perform open-hole compressive tests on multi-directional polymer matrix composite laminates reinforced with high .

Author: Zulkigal Tygozilkree
Country: Kosovo
Language: English (Spanish)
Genre: Medical
Published (Last): 28 August 2009
Pages: 185
PDF File Size: 12.48 Mb
ePub File Size: 8.27 Mb
ISBN: 828-5-54121-723-9
Downloads: 38308
Price: Free* [*Free Regsitration Required]
Uploader: Nanos

The calculations shown are based upon actual measured sample thickness and width. The range of acceptable test laminates and thicknesses are described in 8.

Precision and Bias Retests shall be performed for any specimen on which values are not calculated. Factors that influence the notched compressive strength and shall therefore be reported include the following: While the hole causes a stress concentration and reduced net section, it is common aerospace practice to develop notched design allowable strengths based on gross section stress to account for various stress concentrations fastener holes, free edges,? The xstm level may be increased above this level when acceptable failure modes cannot be achieved using 7 N-m [60 in-lbf] applied torque.

A cutout exists on both faces of the?

Standard test specimens are 36 by mm [1. Sampling and Test Specimens 8. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.

  FARMACOLOGIA VETERINARIA SUMANO OCAMPO PDF

Summary of Test Method 4. In laminated composites, the principal material coordinate system has meaning only with respect to an individual orthotropic lamina.

However, they can be bene? The assembled fixture, with specimen installed, can be gripped at each end by hydraulic grips in the testing machine shear loadingor aligned vertically between flat platens end loading. Unless coupon rupture is speci?

ASTM D Open-Hole Compressive Strength of Polymer Matrix Composite Laminates_图文_百度文库

Results may also be affected by the ratio of ungripped specimen length to specimen width; this ratio should be maintained at 2. Sources of Additional Information: The following general zstm apply to these?

Work Item s – proposed revisions of this standard. Tolerances may be applied to a nominal value to de? Each laboratory tested at ambient laboratory conditions a randomly distributed sample of six specimens for each loading type.

ASTM D Open-Hole Compression (OHC) Testing of CFRP Video | LabTube

This may result in non-conservative data. This laminate has relatively high stiffness with high notch sensitivity and was selected to produce high failure forces in order to evaluate the two loading methods using test laminate parameters representing the upper capability of the test method. If the specimen is to be failed, record the maximum force, the failure force, and the head displacement at, or as near as possible to, the moment of rupture.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

  DIN 51802 PDF

ASTM D6484 Open-Hole Compression (OHC) Testing of CFRP

Originally approved in This should result in the specimen hole being centered in the? Reduce the compressive force to 7 N [30 lbf], and re-zero and balance all instrumentation. The ends of the grip-jaws on wedge-type grips should be even with each other following insertion to 11 avoid inducing a bending d64484 which could result in premature failure of the specimen.

This notation uses the? One of the reference coordinate system axes normally the Cartesian x-axis is designated the reference axis, assigned a position, and the ply principal axis of each ply in the laminate is referenced relative to the reference axis to de? A rectangle should be 4 FIG. If the fixture is loaded between flat platens, some type of lateral constraint should be provided so that the fixture does not slip out from between the platens while being compression loaded, as a safety precaution.

Individual reprints r6484 or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.