I am a Dek

Designed for the contractor, the CPS MK II feature 2-RU chassis, Phoenix-type connectors for inputs and outputs, pre-programmable power-on delay, easy power-on via remote contact closures, rear panel attenuators, and a switchable 50 Hz high-pass filter. Like the CPS multi. Two-Channel Models CPS, CPS, CPS, and CPS CPS2.x rear view. Remote power-on contact. 1. Programmable power-on timer. 2. Module slot for. Buy Electro-Voice CPS 2-Channel Power Amplifier for RCM IRIS-Net Remote Control Module (W, 4 Ohms) Review Electro-Voice CPS

Author: Voodoozragore Duzuru
Country: Lesotho
Language: English (Spanish)
Genre: Medical
Published (Last): 13 July 2012
Pages: 147
PDF File Size: 10.96 Mb
ePub File Size: 7.61 Mb
ISBN: 215-4-40449-277-2
Downloads: 95301
Price: Free* [*Free Regsitration Required]
Uploader: Maugami

The power amplifier remains cooler and dissipating the developing waste heat in a specific direction gets easier. The audio signal has to be applied to the input connectors of channel 1, amplification is set via input level control of channel 1 cpa2.9. Otherwise, a 6 dB drop in level could result.

Electro-Voice CPS2.9

The Mains Switch on the front panel separates the power amp from the mains. The exclamation point within an fps2.9 triangle is intended to alert the user to the presence of important operating and maintance servicing instructions in the Speaker system switch-on is delayed by approximately 2 seconds via output relays, effectively suppressing any possible power-on noise, which otherwise might be heard through the loudspeakers.


Also See for CPS2. Electrovoice contractor precision cps1: Following table shows possible switch settings and corresponding delay times.

ProSoundWeb Community

The audio signal has to be applied to the input connectors of channel 1. Don’t have an account? Extremely high voltages can be vps2.9 at the output.

Inputs are electronically balanced. For pricing options and packages, contact us at The power drawn from the mains network is converted into output power to feed the connected loudspeaker systems and into heat. Keep ventilation louvers free from dust to ensure unhindered airflow. F reserved Table 4.

Set the switch to the OFF position if no attenuation of low frequency audio signals is required.

Electro-Voice Cps MKII Contractor Class-h Power Amp 2x Watts | eBay

When installing the power amp in a case or rack system, attention should be paid to these details to provide sufficient ventilation. Mounting CPS amplifiers have been designed for installation in a conventional inch rack case. In DUAL mode, the two eg of the power amplifier work independent from each other. Don’t show me this message again.

Electro-Voice CPS 2-Channel – Contractor Precision Series Power Amplifier

The difference between power consumption and fps2.9 power is called power dissipation P d. Make sure to completely read and fully observe power rating specifications of the speaker systems to be used and to check them against the output power capacity of the power amp.


The power amplifier remains cooler and dissipating the developing waste heat in a specific direction gets easier. Got it, continue to print.

The connected speaker systems must be able to handle such voltages. Electrovoice compact precision cps: During installation, always separate the power amplifier from the mains.

Due to their immunity against external interference sources, such as dimmers, mains connections, HF-control lines, etc.

A soft start circuit compensates mains inrush current peaks and thus prevents triggering AC mains fuse when switching on the amplifier. In this case, bridging the screen shielding and the pin of the inverting input inside of the connector is mandatory. Table of Contents Add to my manuals Add. Enter text from picture: Mains Switch Cps.9 View 1.

As with all Electro-Voice power amps with fan cooling, the airflow direction is front-to-rear, obviously because there is more cold air outside of the rack case than inside.